This master thesis has been performed at Vattenfall Power Consultant in Gothenburg and Trollhättan for Vattenfall Vattenkraft. In this report vacuum circuit breaker in small-scale hydropower stations with the rated power 4 MVA and below has been studied. Models of the stations are modeled and analyzed in PSCAD/EMTDC to study the High voltage transients that are created after current chopping with vacuum circuit breaker. Vacuum circuit breaker may chop the current before it reaches zero value, which means that High voltage transients can be created. The equipment of the stations can be destroyed by High voltage transients.The purpose of this thesis is to examine the use of vacuum circuit breaker in small-scale hydropower stations and the risk for High voltage transients from current chopping.According to the results there is a risk of High voltage transients after current chopping with small synchronous generators in stations with the operating voltages 0.4 kV and 3.6 kV.

The voltage regulation in Fortum Distributions medium voltage network in Stockholm does not work satisfactory. This results in too high distribution voltages with many customer complaints as a consequence. The reason is the model responsible for compensating for voltage drops in the distribution network. Despite several adjustments Fortum has not been able to find the source of the High voltages and has therefore appointed an investigation in the form of a thesis work.The aim of this investigation is to locate the error and to produce a proposal regarding the solution of this error using the existing system, common industrial knowledge, state of the art research and the option to use voltage readings from the different substations.The conclusion of this master thesis is that the largest contribution to the High voltage levels is made by the large compensation for distribution loses. Furthermore an additional error in the model has been found.

This master thesis deals with problems in the arc length control in Pulsed MIG/MAG Welding. The main problem is that it is not possible to measure the arc length. In the present solution the voltage over both the electrode and the arc represents the arc length. To improve the arc length control a model of the electrode melting has been built. One output from the model is the voltage over the electrode and with this voltage together with the measured voltage it is possible to calculate the voltage over just the arc.

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

In this thesis a rural network in Norrbotten, Sweden, has been to designed and planned with the purpose of improving distribution reliability by exchanging existing overhead lines with underground cables. General network design considerations are discussed as well as the ones for the specific low voltage grid. During the design phase the maximum power of domestic consumers has been estimated using Velander?s method. Currents, voltage drop and impedance of the network have been calculated and fuse operation and selectivity has been considered.

This report describes the development of a high-voltage connector at the request of Scandinova Systems AB in Uppsala. The development process is described from the making of a customer demand specification, to the making of drawings for the manufacturing of prototypes. Scandinova develops high-voltage modulators, hence the need for connectors that can handle very large power pulses. Their current connector has several weaknesses that may cause the connector to melt or catch fire. The development began with a number of studies that included the modulator structure and the current connector structure and functions.

Microproduction, also called distributed generation, is something that has become more and more popular in the electric grid. Microproduction can however lead to unacceptable performance if several units are installed in the same low voltage network. It is therefore good to know a limit where the performance of the low voltage network becomes unacceptable based on given parameters. This limit is usually called hosting capacity.In this report the hosting capacity with respect to voltage and current have been studied in three low voltage networks which are located in Falu Elnäts concession area. This has been done by simulations in a GIS-program where critical times of the grid have been simulated.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.